Introduction: The Dual Drive of "Localization" and "Intelligence" in Train Control Equipment
In October 2026, the National Railway Administration of China officially issued the "15th Five-Year Plan for Railway Science and Technology Innovation", explicitly listing the independent and controllable development of core train control chips as the top priority task. According to disclosures at the 2026 semi-annual performance briefing of Siwei Train Control, there are approximately 34,000 existing sets of the domestic LKJ train control system, which is now entering a critical window for upgrades and replacements. Meanwhile, the R&D of the new-generation conventional speed train control system (CTCS-1) and the locomotive intelligent auxiliary driving system (STO) is comprehensively accelerating. As the "brain" of rail transit, the embedded hardware architecture of train control equipment is undergoing profound changes from underlying chips to system integration. This article will combine the latest industry trends to deeply analyze the embedded safety architecture and domestic substitution technology path behind the railway train control GYK/LKJ systems.
1. SIL4 Safety Baseline: Triple Modular Redundancy Architecture and FPGA Collaboration
Railway train control systems (such as LKJ and CTCS) have extremely stringent safety requirements, reaching the strict SIL4 level, meaning the probability of dangerous failure must be less than 1 per 100 million operating hours. Under the guidance of the "15th Five-Year Plan", domestic train control SoCs have fully adopted the Triple Modular Redundancy (TMR) architecture. The chip internally sets up three completely independent computing units that execute instructions synchronously. Once a deviation occurs in the output results, the system will immediately eliminate the error and trigger emergency braking.
At the embedded board development level, in addition to the SoC's own redundancy, peripheral logic usually relies on FPGA for safety voting and interface isolation. The FPGA's radiation resistance, wide-temperature operating characteristics (-40°C to +85°C), and deterministic delay make it a core component of the train control safety computer. In the design, it must be ensured that the high-speed bus (such as SRIO, PCIe) between the FPGA and SoC maintains signal integrity (SI) in strong electromagnetic interference environments, which requires the PCB design to strictly follow impedance control and equal-length matching rules.
2. Intelligent Perception and Video Processing: RK3588 Empowering LKJ Auxiliary Driving
As the LKJ system evolves towards intelligence, the Locomotive Intelligent Auxiliary Driving System (STO) and the Intelligent Lookout and Anti-Collision System have become the focus of the industry. Northwest Railway Electronics' recently acquired patent for the "Map Data Fusion Method for Intelligent Lookout and Anti-Collision of Railway Trains", as well as Traffic Control Technology's virtual train consist technology, both rely on the real-time fusion of multi-source sensor data.
In this context, embedded boards based on multi-core heterogeneous SoCs such as the RK3588 show huge advantages. The RK3588 has a built-in NPU with 6TOPS computing power and a powerful ISP, capable of efficiently processing multi-channel high-definition camera video streams and millimeter-wave radar data. In Qiyun Zhixun's embedded solutions, the RK3588 core board can achieve:
- Multi-source data fusion: Pixel-level alignment and fusion of railway-specific high-precision maps, train control ground basic data, and real-time video streams.
- Edge AI inference: Utilizing the NPU to run deep learning algorithms for track obstacle recognition, signal light status detection, and OCR capture of DMI (Driver Machine Interface) information.
- High-reliability video output: Supporting multi-channel asynchronous display to ensure crew members receive real-time safety warnings and driving suggestions.
3. PCB Design and SI/PI Challenges under Full Domestic Substitution
From Jiaoda Sinuo's TCR equipment achieving 100% domestic chip substitution, to Siwei Train Control's CMD2.0 system completing fully domesticated design and operational tests, the "chip disease" of railway train control equipment is being thoroughly cured. However, the substitution of domestic components is not a simple Pin-to-Pin replacement, bringing new challenges to PCB design.
Domestic chips often differ from foreign original solutions in packaging substrate materials, BGA pin definitions, and internal timing. Direct replacement can easily trigger Signal Integrity (SI) and Power Integrity (PI) issues.
In high-speed backplane design and core board development, 3D electromagnetic simulation must be introduced. For domestic DDR4/DDR5 memory chips and domestic Gigabit/10-Gigabit Ethernet PHY chips, channel simulation and via optimization need to be re-conducted. In addition, train control equipment mostly adopts a sealed chassis fanless design. Changes in the power consumption distribution of domestic chips require strict thermodynamic simulation for PCB layout. By increasing copper area and optimizing thermal via arrays, stable system operation under high-temperature conditions is ensured.
4. Hardware-in-the-Loop (HIL) and LKJ Automated Simulation Testing
Embedded safety relies not only on design but also on rigorous testing and verification. According to relevant literature on "Research on LKJ Automated Simulation Testing", traditional manual testing suffers from pain points such as low coverage and difficulty in reproducing defects. Currently, automated simulation testing platforms based on Hardware-in-the-Loop (HIL) have become the standard for LKJ software R&D.
Such testing platforms need to generate multiple types of physical signals in real-time (such as speed, track circuit signals, brake pipe pressure) and simulate DMI inputs through robotic arms or vision systems. Qiyun Zhixun's experience in military and rail transit testing shows that using high-performance FPGAs to build real-time IO simulation nodes, combined with the RK3588 for video acquisition and machine vision comparison, can establish a microsecond-level delay calibration model. This achieves precise synchronization between external signal injection and internal LKJ recording, increasing test repeatability to 100%.
Conclusion
From the triple modular redundancy of underlying SoCs to the intelligent perception of the RK3588, from fully domesticated PCB design to HIL automated testing, every iteration of the railway train control GYK/LKJ system is a challenge to the limits of embedded hardware design. Xi'an Qiyun Zhixun Electronic Technology Co., Ltd. will continue to deeply engage in high-reliability PCB design, FPGA logic development, and heterogeneous computing platforms, providing solid underlying hardware support for the 100% independent and controllable development and intelligent upgrade of China's railway equipment.